The OxeDot is a wireless control device that can load and unload the XS1 system. Instead of pressing the LOAD button to start an exercise, use the OxeDot when the system is ready to start. Attach the OxeDot to any OxeFit accessory and position it where you can easily press it throughout your exercise.
One OxeDot is included in each XS1 accessory package (Flex, Flow, and Peak), and it connects automatically to the device. Your XS1 will support up to three OxeDots at the same time. You must pair each additional OxeDot in order to start using it. See CONNECTING NEW/MULTIPLE/DISCONNECTED OXEDOTS.
HOW IT WORKS
CHECK TO SEE IF OPERATIONAL
While near the XS1, press the OxeDot to ensure the battery is operational. If there is no light when you press the OxeDot, see CHANGING THE OXEDOT BATTERY.
CONNECTING
Once the OxeDot is confirmed to have an operational battery, it will connect automatically to the XS1 when pressed. If the OxeDot does not connect automatically, wait two minutes before pressing the OxeDot again. If the OxeDot does not connect after two minutes, press the accessory again to restart the pairing process. See CONNECTING NEW/MULTIPLE/DISCONNECTED OXEDOTS.
HOW TO USE
- Press and hold the OxeDot for at least one second to start and load the exercise.
- Press the button again to unload the exercise.
CONNECTING NEW / MULTIPLE / DISCONNECTED OXEDOTS
Pair new or multiple OxeDots to your XS1. You can have up to three OxeDots connected to your device at the same time.
Although the OxeDot should not disconnect after being paired, use the following steps to pair previously connected OxeDots that are no longer connected to the XS1.
- Ensure the XS1 is not in sleep mode by tapping anywhere on the touchscreen.
- Press the OxeDot.
- Navigate to the drop-down menu in the top right corner of the XS1 screen.
- Select BLUETOOTH.
- Allow the system to scan to find the OxeDot. If the OxeDot is not listed after one minute, close the Bluetooth settings.
- Open the Bluetooth settings and allow it to scan again. If the OxeDot is not listed after 30 seconds, press REFRESH.
- If the OxeDot continues to not list under Devices, select FORGET ALL OXEDOTS. Then, select FORGET to confirm.
- Close the Bluetooth settings, then reopen the Bluetooth settings and allow the system to scan to find the OxeDot.
- Once the OxeDot is listed under Devices, press CONNECT. The OxeDot will then be removed from the list.
- Close the settings.
- Allow the system two minutes to connect to the OxeDot.
YOUR OXEDOT CODE
Verify which OxeDot is listed under Devices by completing the following steps:
- Ensure the OxeDot is upright. The chevrons in the logo should be on the left side of the X and the back clip’s opening should be pointing down.
- Open the OxeDot by twisting the front portion of the device counterclockwise.
- Access the Bluetooth settings by navigating to the drop-down menu in the top right corner of the screen and selecting BLUETOOTH.
- View the code within the accessory and match it to an OxeDot listed under Devices in the Bluetooth settings. NOTE: If your OxeDots are not listed, select FORGET ALL OXEDOTS, then press the OxeDot to reconnect and view on the list.
- Close the OxeDot by connecting the front and back of the OxeDot and aligning the logo’s center to the left of the top center of the device (see image below) before twisting the front portion clockwise.
HOW TO CHANGE THE OXEDOT BATTERY
The OxeDot requires a CR2032 battery. If there is no light when you press the OxeDot, change the battery by completing the following steps:
- Ensure the OxeDot is upright. The chevrons in the logo should be on the left side of the X and the back clip’s opening should be pointing down.
- Open the OxeDot by twisting the front portion of the device counterclockwise.
- Using a non-metallic object, slide the battery out and replace it with the + side facing away from the circuit board. NOTE: If there is a small clip blocking the battery from sliding out, gently lift the clip as you remove the battery. You can fold the clip slightly inward to prevent it from blocking the battery in the future.
- Close the OxeDot by connecting the front and back of the OxeDot and aligning the logo’s center to the left of the top center of the device (see image below) before twisting the front portion clockwise.
Comments
0 comments
Article is closed for comments.